|
America West Drilling Supply...Where going in the hole makes sense!
Drill String Accessories
Automatic Breakout System
Automatic Lug Pipe Breakout System
Automatic breakout unit can be adapted to any type of top head drive unit. Illustrated is the 2000 series top head drive.
|
|
Parts List for Automatic Breakout System |
Item |
Quantity |
Description |
1 |
1 |
Mounting clamp |
2 |
1 |
Arm |
3 |
1 |
Pivot bracket |
4 |
1 |
Cylinder |
4A |
1 |
Pivot mount bracket |
4B |
1 |
Retaining pin |
5 |
1 |
Clevis |
6 |
1 |
Auto. breakout sub |
7 |
2 |
Bearing retainer bolt |
8 |
2 |
Bearing |
9 |
1 |
Cap assembly |
10 |
1 |
Barrel assembly |
11 |
1 |
Barrel support ring |
12 |
1 |
Shift yoke |
|
Automatic Flush Pipe Breakout System
The unit can be either hydraulic or air-operated. Normally the unit is operated by the backup pressure of the hydraulic return line.
Parts List for Automatic Breakout System |
Flush Pipe Breakout System
|
Item |
Quantity |
Description |
1 |
1 |
Outer barrel |
2 |
1 |
Inner sleeve |
3 |
1 |
Breakout key |
4 |
1 |
End cap |
5 |
1 |
Key |
6 |
1 |
O-ring |
7 |
1 |
Cap assembly |
8 |
16 |
S.H.C.S. screw |
9 |
2 |
Snap ring |
10 |
2 |
HHCS capscrew |
11 |
2 |
Drive key |
12 |
2 |
Retainer ring |
13 |
1 |
Breakout sub |
14 |
1 |
Stem |
15 |
1 |
O-ring seal |
16 |
1 |
Yoke |
17 |
1 |
Pivot bracket |
18 |
1 |
Hydraulic cylinder |
19 |
1 |
Clevis |
20 |
2 |
Retaining pin |
21 |
2 |
Bearing retainer bolt |
22 |
1 |
Bearing |
23 |
1 |
Arm |
24 |
1 |
Mounting bracket |
Automatic Breakout Unit for Flush Drill Pipe
Operating Instructions: Automatic Breakout Unit for Flush Drill Pipe
The Automatic Breakout for Flush Drill Pipe is used when the desired depth has been reached in the drilling of a well to provide a backup when breaking out the drill pipe without the use of wrenches.
In operation the Automatic Breakout (ABO) Unit operates in the following sequence:
- Once the desired depth has been reached, pick up and set the slips on the first joint.
- Break-out this connection, but do not spin fully out of the connection.
- Activate the ABO Unit, allowing the Back-off Barrel to lower.
- Begin slow rotation to the right, this will allow the Lock Ring to align with the flats and the Back-off Barrel will drop.
- Pull up the next joint, set the slips, break, and spin out first joint.
- Lower the drill pipe to the stand or floor, release the ABO Unit, and spin out the first joint.
- Lower head to make up the next joint.
- Spin into this connection, but do not torque up connection.
- Activate the ABO Unit and repeat Steps 2-9.
|
Wegelock Connector
Advantages:
- Positive rotation in either direction
- Safety - Will not back out when reversing rotary head
|
|
 |
- Ease of disassembly after prolonged use
- Custom Design for any size connection and any torque.
|
AutoSlips
Parts List for AutoSlip Base |
An automatic slip has been developed for holding any size pipe up to 4" and down to 3/4". |
Item |
Quantity |
Description |
1 |
1 |
Slip case assembly |
2 |
1 |
Top plate |
3 |
2 |
Hydraulic cylinder |
4 |
2 |
Hydraulic line - extend |
5 |
2 |
Hydraulic line - retract |
6 |
30 |
Socket heat capscrew - 3/8-24NF x 1.00 long |
7 |
2 |
Slip jam carrier |
8 |
4 |
Socket head capscrew - 3/8-16NC x 2.25 long |
9 |
2 |
Slip for 3 1/2" auger |
10 |
2 |
Slip for 2 3/8" pipe |
11 |
2 |
2 3/8 guide plate |
12 |
2 |
Socket head capscrew - 3/8-16NC x 1.00 |
13 |
2 |
3/8" roll pin x 3/4" long |
Slips for Breakout for Lugged Drill Pipe or Casing
3" Casing Slips with
Breakout Flats for Lugs |
1 1/2" and 2" Pipe Slips
with Breakout Flats for Lugs |
Locking-Type Slips used for Automatic
Breakout on Pipe with Lugs
|
