America West Drilling Supply...Where going in the hole makes sense!
Flags
Flags

Red Hawk

Built to last

Breaking concrete, Cutting asphalt, Tamping, Digging

Gas-Powered Breaker

Red Hawk

Freedom of movement, zero set-up time

From the leading supplier of demolition tools comes the Red Hawk gas-powered breaker. Tough and well designed, the Red Hawk is ideal for small jobs or for working in remote locations.

With no compressors, hoses, or cables to set up, gas-powered breakers are ideal for smaller jobs. An impressive range of tools make the Red Hawk extremely flexible and the 7/8" and 4 1/4" steels make for rapid penetration of concrete.

A multi-purpose tool

With a wide range of tools, you can use the Red Hawk for everything from cutting and breaking to driving and compacting. Whether you need to just break a small patch of concrete or drive a tent stake you can get the job finished with a gasoline-powered machine in the same amount of time it takes to set up a compressor and hoses.

Use the rugged and versatile Red Hawk to:

  • break concrete
  • cut asphalt
  • dig
  • drive posts and fences
  • drive rods and spikes
  • tamp and compact soil
  • tamp ballast/ties
AWDS Logo
Gas-Powered Breaker in use

Low emissions, vibrations, and noise level

Red Hawk is a modern tool that meets emerging regulations. Equipped with a catalytic converter and newly designed carburetor, the machine meets tough U.S. emission regulations EPA1.

 

In addition, a silencer has reduced the noise level from 114 dB to 107 dB, thereby fulfilling the European Emission Directive.

 

 Gas-powered breaker

Vibration-dampening handles
Easy to start

Vibration-dampening handles

Vibration-dampening handles have reduced vibration levels from 8 to less than 4.8 m/s2.
Easy to transport

Easy to start

With a choke control, carburetor, and user-friendly instructions, the Red Hawk is easy to start.

An optional guide roller makes it easier to pull downwards to start the machine when it is placed higher up.

Easy to transport

The Red Hawk weighs
in at about 50 lbs.
Each comes with
its own carrying case
which fits easily into
the trunk of your car.

Technical data

Model
Wt.
L
D
Width over
handles
Tool
shank
Sound
level
Vibration
level
 
lb.
in.
in.
in.
in.
(Acc. to ISO 3744)
(Acc. to ISO 8662)
Red Hawk
50.5
27.3
11.0
23.0
7/8" - 4 1/4"
107 dB
4.7 m/s2


Engine

Type
Power
Cooling
system
Starter
system
Recom.
fuel
Oil type
Oil
mix
185 cc 1-cylinder,
2-stroke
1kW
Forced air
Recoil starter
Unleaded
synthetic
two-stroke oil
2% 1:50

Type
Fuel capacity
Fuel consumption
Impact rate
185 cc 1-cylinder,
2-stroke
0.31 U.S. gal.
0.36 U.S. gal./hour
2600 BPM

A tool for every job

The manufacturer maintains a comprehensive range of chisels so that you can select the right tool for the job. Their chisels are among the hardest wearing on the market. A controlled heat treatment process imparts both strength and high wear resistance to deep surface layers while maintaining a tough shock resistant central core to resist breakage. The striking face is end-milled. This results in better contact between the piston and the tool, improved transfer of energy, as well as less vibration and wear on both hammer and chisel.

  Tool type
Working length
Tip width

Weight

Tools

Tool listing breakdown
  Shank H 7/8 x 4 1/4 in.
in.
in.
lb.
1
 Tie tamper
15 1/2
3 1/2
6.5
  Tie tamper
18
3 1/2
7.0
  Tie tamper
22
3 1/2
8.5
2
 Moil point
14
3 1/2
3.1
  Moil point
19
  
4.5
3
 Wide chisel
9 1/2
1 3/4
2.7
  Wide chisel
13 1/2
1 3/4
3.1
  Wide chisel
15
3
5.7
  Wide chisel
18
1 3/4
4.5
4
 Asphalt cutter
14
5
6.5
5
 Digging chisel
11
3
6.0
6
 Digging spade
13
4 3/4
8.0
7
 Wedge set 29 mm    
3.3
  Wedge set 34 mm    
4.6
8
 Ground rod driver
7 3/4
1 11/16
2.6
9
 Clay spade
14
5
7.5
10
 Wedge chisel
15
1 3/8
6.2
11
 Driver blank
7 3/4
2 1/8
5.5
12
 Shank for pad
7 1/4
 
2.9
13
 Tamping pad, round  
7
16.5
14
 Tamping pad, square  
7
12.5
15
 Tamper sq., compl.
7 1/2
7
15.5
16
 Driver pad, round  
4
5.5
17
 Post hole driver
18
Ø 1 1/2
9.2
18
 Stake driver (2.5")  
2 1/2 ID
11.0
19
 Shank for 2.5" stake driver
9
  
4.6

Accessories

20
 Guide roller Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.
21
 Carrying harness